Soffit and fascia are the two parts of your roofline that do the most quiet work: fascia is the vertical board that caps the ends of your rafters and carries the gutters, and soffit is the panel that closes off the underside of the overhang. When either starts to fail, the price to fix it depends far more on how much is damaged and what's behind it than on the boards themselves. This guide gives you the full 2026 picture — the same framework a contractor uses when writing an estimate — so you can read a quote with confidence instead of guessing.
Soffit & Fascia Cost — Quick Summary
Here's what homeowners typically pay in 2026 across the most common scenarios, assuming aluminum or vinyl on a single-story home with standard access:
| Project Scope | Typical 2026 Cost |
|---|---|
| Minor spot repair (1–3 boards/panels) | $300–$700 |
| Section repair (one run or one side) | $700–$1,800 |
| Full replacement — single-story home | $2,500–$4,500 |
| Full replacement — two-story home | $4,000–$7,500 |
| Structural repair (rafter tail / subfascia) | $500–$2,000 add-on |
Cost Per Linear Foot
Contractors price soffit and fascia by the linear foot — the distance measured along the roofline, not square footage. This is the most reliable way to sanity-check a quote. The ranges below include both materials and labor.
| Component | Repair (per LF) | Full Replacement (per LF) |
|---|---|---|
| Soffit | $4–$12 | $6–$20 |
| Fascia | $5–$14 | $7–$22 |
| Soffit + fascia combined | $8–$20 | $12–$30 |
An average single-story home has 150–200 linear feet of roofline. A two-story or complex roof with many gables, dormers, and corners can exceed 300 linear feet, which is why footprint and roof complexity move the price so much.
Estimate Your Project — Free Calculator
Enter your approximate roofline length, choose a material and scope, and get an instant ballpark range. This is an estimate for planning — a free on-site inspection gives you an exact written number.
Cost by Material
Material choice affects both the up-front price and how long the job lasts before you're paying again. Aluminum is the most common replacement material because it balances cost and durability, but the right choice depends on your climate and the look you want to keep.
| Material | Combined, installed (per LF) | Lifespan | Best For |
|---|---|---|---|
| Vinyl | $10–$20 | 20–30 yrs | Budget projects, mild climates |
| Aluminum | $14–$28 | 25–40 yrs | Most homes; coastal & high-sun areas |
| Wood | $22–$40 | 10–20 yrs | Historic / architectural matching |
| Composite / PVC | $24–$44 | 30–50 yrs | Wet climates, low-maintenance priority |
Wood costs the most to install and maintain because it needs periodic paint and is the most rot-prone — which is exactly why many homeowners replacing wood soffit switch to aluminum or PVC unless architectural rules require wood.
Cost by U.S. Region
The biggest reason two identical homes get different quotes is local labor rates. Since labor is 50–70% of the bill, regions with higher construction wages cost more. The table below shows the typical range for a full replacement on an average single-story home (~175 linear feet) in 2026.
| Region | Typical Full Replacement | vs. National Avg |
|---|---|---|
| West Coast (CA, OR, WA) | $3,400–$6,800 | +15–20% |
| Northeast (NY, PA, New England) | $3,200–$6,500 | +10–15% |
| Southeast (FL, GA, SC) | $2,600–$5,200 | Near average |
| Midwest (OH, IL, MN, IA) | $2,500–$5,000 | −5% |
| South / Southwest (TX, AZ, NM) | $2,400–$4,800 | −5–10% |
Coastal areas within the Southeast — the Florida Gulf and Atlantic coasts especially — often run at the top of their regional range because salt air forces more frequent aluminum and PVC work. You can find city-level pricing on our location pages.
What Drives the Price Up or Down
1. Hidden structural rot
Panels and boards are cheap; the structure behind them is where budgets blow up. If moisture has reached the subfascia or rafter tails, that wood must be rebuilt before new material goes on — adding $500–$2,000 or more. This is the single most common reason a quote comes in higher than a homeowner expected.
2. Gutters
Fascia carries the gutters, so gutters usually have to come down and be re-hung during fascia work. If the gutters are old or damaged, many homeowners replace them at the same time — it's far cheaper to do both while the crew and ladders are already up.
3. Roof complexity and height
Every gable, dormer, and corner adds linear feet and slows the work. Two-story access requires taller ladders or scaffolding and adds roughly 20–40% to labor. A simple ranch roofline is the cheapest to service.
4. Material and finish
Wood and premium composites cost more than vinyl and aluminum, and custom colors or wrapped fascia (aluminum capping over wood) add labor. See the aluminum vs. vinyl comparison for how the two most common options stack up.
Detailed Cost Breakdowns by Service
This guide covers the combined project. For line-by-line pricing on a specific job, see the focused breakdowns:
- Soffit repair cost — spot repairs to full soffit replacement
- Soffit replacement cost — full tear-off and rebuild pricing
- Fascia replacement cost — board, capping, and drip-edge pricing
- Gutter installation cost — seamless gutter pricing that often pairs with fascia work
How to Get an Accurate Estimate
Every number on this page is a planning range. The only way to know your real cost is a ground-and-ladder inspection that finds hidden rot before you commit. A written, itemized estimate should separate materials, labor, and any structural repair line items — if a quote is a single lump sum with no breakdown, ask for one. Soffit Fascia Repair connects homeowners with licensed local contractors who provide free written estimates with no obligation. Call (855) 606-2187 to schedule.
Frequently Asked Questions
How much does it cost to replace soffit and fascia?
Replacing soffit and fascia together costs $12–$30 per linear foot installed, or roughly $2,500–$6,000 for a typical single-story home with 150–200 linear feet of roofline. Two-story homes, wood material, and rotted structure behind the boards push the total higher. Repairs to limited sections cost far less — often $300–$1,500.
What is the cost of soffit and fascia per linear foot?
Installed per-linear-foot costs run $6–$20 for soffit and $7–$22 for fascia. Combined, most homeowners pay $12–$30 per linear foot for full replacement including materials and labor. Simple repairs over sound structure fall at the low end; wood, two-story access, and hidden rot fall at the high end.
Why is soffit and fascia so expensive to replace?
The material itself is inexpensive — most of the cost is labor at height. Work happens on ladders or scaffolding along the entire roofline, gutters often must come down and go back up, and any rotted subfascia or rafter tails must be rebuilt first. Structural repair alone can add $500–$2,000.
Is it cheaper to repair or replace soffit and fascia?
When damage is confined to less than about 25% of one elevation and the structure behind is sound, repair is cheaper. When rot is spread across multiple sides or the nailing channel and subfascia have failed in several places, full replacement often costs less than repeated piecemeal repairs — and avoids mismatched panel colors.
Does homeowners insurance cover soffit and fascia replacement?
Insurance typically covers sudden, accidental damage — storm wind, hail, falling limbs, or animal intrusion. Gradual rot from age or deferred maintenance is excluded. If a storm caused the damage, document it with photos and file promptly, because wind damage to soffit and fascia often qualifies for a claim.
How much does labor cost to install soffit and fascia?
Labor runs about $2–$7 per linear foot for each component and typically makes up 50–70% of the total bill. Because the work is done at height along the full roofline, labor is the single largest cost driver. Regional wage differences are the main reason costs vary from one part of the country to another.